D/F Water-Cooled Semi-Automatic "Mighty MIG" Hand-Held Curved Gun
The NCC-16 "Mighty MIG" gun assemblies utilize the same forward nozzle/gas nozzle assemblies and features of the pistol grip. This allows a flexible and low inventory of replacement parts due to interchangeability of these models using .035" through 1/8" diameter wire. The trigger switch assembly is the momentary contact type. Also available is the optional button on/off switch. Both switches are positionable where desired, at any point 360° around the standard 8" torch handle. Some like to position the switch below the handle as a normal finger trigger, and others might position the switch above the handle for use as a thumb button. These options will help provide comfort and balance, and to escape reflective heat.
Remember the great ESAB ST-16 torch (part no. 997498) that was used exclusively for gas metal arc (MIG) spot welding of aluminum and hard wires? Very similar in design to the ESAB ST-16 but with improvements and new features, and proven to be a superior replacement alternative, the D/F water-cooled handheld curved MIG push gun is a rugged, all purpose, water-cooled, manual MIG welding torch designed to operate at welding currents up to 400 amperes on a true continuous duty cycle using all types of shielding gases. The DF curved MIG gun is intended for use with all wire feeders which have provision for water cooling. It is designed to run wire with diameters up to 3/32". For larger wire diameters 3/32"-1/8", choose from next two sets of models below.
Each D/F gun is fully assembled and ready to install. In order to make the installation complete, the code number, wire size, make/model (Lincoln wire feeders, Miller wire feeders, Tweco wire feeders, ESAB wire feeders, & EURO Quick-Disconnect wire feeders), and inlet as needed must be specified when ordering. If special welding tools or accessories other than those listed previously are required, please consult with the factory. Get the Right Feeder Adapter Connection to Fit Your MIG Wire Feeder.
MODEL EXPLANATION NCC-16 - Normal Duty, Collet Action (Slip-In Tip), Curved
FEATURES
- Water-Cooled Inner Body & Nozzle
- Small Frontal Area for Hard-to-Reach Locations
- Quick-Disconnect Available
- Standard 8" Body Tube & 360° Positionable Trigger Switch
- Optional 360° Positionable On/Off Switch with Round Button
| NCC SPECIFICATIONS |
| Current Capacity |
400 amp
|
| GUN DIMENSIONS |
Reach Length
|
3.5" |
| Length of Body Handle |
8" |
| Diameter of Body Handle |
1.500" |
| Recommended Wire Diameter Range |
.030"-3/32" Hard/Cored 3/64"-3/32" AL |
| Weight (approx., w/out services) |
2.5 lbs. |
| Cooling Required |
5 pints/minute |
ORDERING INFORMATION - STANDARD COMPLETE ASSEMBLIES
|
| Description |
Code No.
|
| 10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
| Model NCC-16 |
11387
|
11388
|
11389
|
D/F Water-Cooled Semi-Automatic Hand-Held Curved MIG Gun
The NCC/HTC curved MIG gun assemblies utilize the same forward nozzle/gas nozzle assemblies and features of the pistol grip. This allows a flexible and low inventory of replacement parts due to interchangeability of these models using .035" through 1/8" diameter wire. The trigger switch assembly is the momentary contact type. Also available is the optional button on/off switch. Both switches are positionable where desired on the torch for comfort and balance, and to escape reflective heat.
Similar to the "Mighty MIG", these models provide options for longer 3", 4", and 5" water-cooled nozzles to meet different job requirements. Each of these lengths comes in the standard diameter, or the Series A high capacity diameter for increased gas coverage.
Remember the great ESAB ST-16 torch (part no. 997498) that was used exclusively for gas metal arc (MIG) spot welding of aluminum and hard wires? Very similar in design to the ESAB ST-16 but with improvements and new features, and proven to be a superior replacement alternative, the D/F water-cooled handheld curved MIG push gun is a rugged all purpose, water-cooled, manual MIG welding torch designed to operate at welding currents up to 600 amperes continuous duty using all types of shielding gases. The DF curved MIG gun is intended for use with all wire feeders which have provision for water cooling and will handle all types of welding wire from .035" diameter through 1/8" diameter flux cored wire, and 3/64" AL through 3/32" Aluminum wire.
The Model NCC-A/HTC-A semi automatic hand held guns provide water-cooled nozzles that accommodate gas nozzles 11/16" through 15/16" I.D. for hard, cored and aluminum wire applications.
Each D/F gun is fully assembled and ready to install. In order to make the installation complete, the code number, wire size, make/model (Lincoln wire feeders, Miller wire feeders, Tweco wire feeders, ESAB wire feeders, & EURO Quick-Disconnect wire feeders), and inlet as needed must be specified when ordering. If special welding tools or accessories other than those listed previously are required, please consult with the factory. Get the Right Feeder Adapter Connection to Fit Your MIG Wire Feeder.
MODEL EXPLANATION NCC - Normal Duty, Collet Action (Slip-In Tip), Curved HTC - Heavy Duty, Threaded Tip, Curved NCC-A - Normal Duty, Collet Action (Slip-In Tip), Curved - High Capacity (Series A) HTC-A - Heavy Duty, Threaded Tip, Curved, Curved - High Capacity (Series A)
FEATURES
- Water-Cooled Inner Body & Nozzle
- Small Frontal Area for Hard-to-Reach Locations
- Nozzle Length may be Extended by Applying Either of Three (3) Different-Length Water-Cooled Nozzle Assemblies
- Quick-Disconnect Available
- Standard 8" Body Tube & Positionable Trigger Switch
- Optional On/Off Switch with Round Button
| HTC/NCC & HTC-A/NCC-A SPECIFICATIONS |
| Current Capacity |
|
| NCC/NCC-A Series |
400 amp |
| HTC/HTC-A Series |
500 amp |
| GUN DIMENSIONS |
| Reach Length w/ 3" Nozzle |
5" |
| Reach Length w/ 4" Nozzle |
6" |
| Reach Length w/ 5" Nozzle |
7" |
| Length of Body Handle |
8"-20" |
| Diameter of Body Handle |
1.500" |
| Recommended Wire Diameter Range |
|
| NCC/NCC-A Series |
.030"-3/32" Hard/Cored 3/64"-3/32" AL |
| HTC/HTC-A Series |
.030"-3/32" Hard/Cored 3/64"-3/32" AL |
| Weight (approx., w/out services) |
2.5 lbs. |
| Cooling Required |
5 pints/minute |
ORDERING INFORMATION - STANDARD COMPLETE ASSEMBLIES
|
| Description |
Code No.
|
| Model NCC (Slip-In Tip) |
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
Short 3" Water-Cooled Nozzle
|
11391 |
11396 |
11401 |
Inter. 4" Water-Cooled Nozzle
|
11392 |
11397 |
11402 |
Long 5" Water-Cooled Nozzle
|
11393 |
11398 |
11403 |
Model HTC (Threaded Tip)
|
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
| Short 3" Water-Cooled Nozzle |
11411 |
11417 |
11421 |
| Inter. 4" Water-Cooled Nozzle |
11412 |
11418 |
11422 |
| Long 5" Water-Cooled Nozzle |
11413 |
11419 |
11423 |
ORDERING INFORMATION - HIGH-CAPACITY COMPLETE ASSEMBLIES
|
| Description |
Code No.
|
| Model NCC-A (Slip-In Tip) |
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
3" Water-Cooled Nozzle (11142)
|
17403 |
17404 |
17405 |
Model HTC-A (Threaded Tip)
|
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
3" Water-Cooled Nozzle (11142)
|
17400 |
17401 |
17402 |
D/F Water-Cooled Semi-Automatic Hand-Held Curved MIG Overlay Gun - External Casing
Similar to the torches above, including the save 3", 4" and 5" lengths in the two diameter nozzle configurations, the NCC-E/HTC-E (External Casing) curved MIG semi-automatic overlay gun assemblies use an axial alignment of the casing to reduce wire feed pressure and improve current tip life. The gun assembly is available with an extended handle (20") and slide switch to help keep the welder away from the extreme conditions of preheat and high amperages required for overlay applications, steel casting repairs, surfacing and rebuilding applications, in the forging industry for the repair or reclamation of forging dies (also utilized in rams, sow blocks, die holders and die shanks when increased hardness is required), and in the steel mill industry for steel gears, arbors, shafts and couplings.
These semi automatic hand held curved torches utilize the same forward nozzle/gas nozzle assemblies and features of the pistol grip torch. This allows a flexible and low inventory of replacement parts due to interchangeability of these models using .035" through 1/8" diameter wire, and are ideal for welding with 3/64" AL and 3/32" AL wire. The trigger switch assembly is the momentary contact type. Also available is the optional button on/off switch. Both switches are positionable where desired on the torch for comfort and balance, and to escape reflective heat.
The model NCCE-A/HTCE-A provide Water-Cooled nozzles that accommodate gas nozzles 11/16" through 15/16" I.D. for hard, cored and aluminum wire applications.
Each D/F gun is fully assembled and ready to install. In order to make the installation complete, the code number, wire size, make/model (Lincoln wire feeders, Miller wire feeders, Tweco wire feeders, ESAB wire feeders, & EURO Quick-Disconnect wire feeders), and inlet as needed must be specified when ordering. If special welding tools or accessories other than those listed previously are required, please consult with the factory. Get the Right Feeder Adapter Connection to Fit Your MIG Wire Feeder.
MODEL EXPLANATION NCC-E - Normal Duty, Collet Action (Slip-In Tip), Curved - External Casing HTC-E - Heavy Duty, Threaded Tip, Curved - External Casing NCCE-A - Normal Duty, Collet Action (Slip-In Tip), Curved, External Casing - High Capacity Nozzle (Series A) HTCE-A - Heavy Duty, Threaded Tip, Curved, External Casing - High Capacity Nozzle (Series A)
FEATURES
- Water-Cooled Inner Body & Nozzle
- Small Frontal Area for Hard-to-Reach Locations
- Nozzle Length may be Extended by Applying Either of Three (3) Different-Length Water-Cooled Nozzle Assemblies
- Quick-Disconnect Available
- Standard 8" Body Tube & Positionable Trigger Switch
- Optional 20" Body Tube & Positionable On/Off Switch with Round Button
| HTC-E/NCC-E & HTCE-A/NCCE-A SPECIFICATIONS |
| Current Capacity |
|
| NCC-E/NCCE-A Series |
400 amp |
| HTC-E/HTCE-A Series |
500 amp |
| GUN DIMENSIONS |
| Reach Length w/ 3" Nozzle |
5" |
| Reach Length w/ 4" Nozzle |
6" |
| Reach Length w/ 5" Nozzle |
7" |
| Length of Body Handle |
8"-20" |
| Diameter of Body Handle |
1.500" |
| Recommended Wire Diameter Range |
|
| NCC-E/NCCE-A Series |
.030"-1/8" Hard/Cored 3/64"-3/32" AL |
| HTC-E/HTCE-A Series |
.030"-1/8" Hard/Cored 3/64"-3/32" AL |
| Weight (approx., w/out services) |
2.5 lbs. |
| Cooling Required |
5 pints/minute |
ORDERING INFORMATION - STANDARD COMPLETE ASSEMBLIES
|
| Description |
Code No.
|
| Model NCC-E (Slip-In Tip) |
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
Short 3" Water-Cooled Nozzle
|
15356 |
15359 |
15362 |
Inter. 4" Water-Cooled Nozzle
|
15357 |
15360 |
15363 |
Long 5" Water-Cooled Nozzle
|
15358 |
15361 |
15364 |
Model HTC-E (Threaded Tip)
|
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
| Short 3" Water-Cooled Nozzle |
15329 |
15332 |
15335 |
| Inter. 4" Water-Cooled Nozzle |
15330 |
15333 |
15336 |
| Long 5" Water-Cooled Nozzle |
15331 |
15334 |
15337 |
ORDERING INFORMATION - HIGH-CAPACITY COMPLETE ASSEMBLIES
|
| Description |
Code No.
|
Model HTCE-A (Threaded Tip)
|
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
3" Water-Cooled Nozzle (11142)
|
17224 |
17225 |
17226 |
4" Water-Cooled Nozzle (11138)
|
17227 |
17228 |
17229 |
5" Water-Cooled Nozzle (45127)
|
17230 |
17231 |
17232 |
ORDERING INFORMATION - HIGH-CAPACITY COMPLETE ASSEMBLIES WITH 20" BODY TUBE & SLIDE SWITCH
|
| Description |
Code No.
|
Model HTCE-A (Threaded Tip)
|
10 Ft. Casing |
12 Ft. Casing |
15 Ft. Casing |
3" Water-Cooled Nozzle (11142)
|
17217 |
17218 |
17219 |
4" Water-Cooled Nozzle (11138)
|
17220 |
17221 |
17222 |
5" Water-Cooled Nozzle (45127)
|
17223 |
17223-12 |
17223-15 |
|